- Power down the hot tub and drain it (15 minutes).
- Wipe down the interior with a soft cloth and gentle cleaner (10 minutes).
- Use the same cleaner to gently wipe down the pillows, control panel, and skirt (5 minutes).
- Wipe down the hot tub cover (2 minutes) and clean the filter (2 minutes).
- Empty the spa to eliminate calcium scales and any algae buildup. A plaster-lined concrete spa can withstand stiff brushing.
Regularly cleaning your hot tub is essential for keeping it in top shape. Use specific cleaning solutions to clean the hot tub’s lines, filter, shell, cover, and exterior cabinet. Drain the hot tub and refill it with fresh water. Experts recommend repeating this process.
To clean the shell of your hot tub, drain it and gather all necessary cleaning supplies. Use a specialized hot tub cleaner to clean the shell, but you can also use a mixture of one part white vinegar and four parts warm water. Avoid mixing bleach and vinegar.
To clean the hot tub shell, gather your supplies, mix equal parts white vinegar and water in a bucket or spray bottle. Gently wipe away the shell above the water line to remove any scum or dirt that has begun to accumulate around the sides of your hot tub not immersed in water.
To clean the filters, use Spa Purge for the plumbing lines. Clean the jets with Jet Clean and drain the hot tub. Fill the bath with cold water above the jet line, remove the filters (if your spa bath has a filter), turn the jets on, and run them for 5-10 minutes. Spray the spa shell with spa cleaner, diluted white vinegar, or diluted bleach, and use a soft cloth or non-scratch nylon scrubber to remove residue and debris.
📹 How To CLEAN Your HOT TUB (Beginner’s Guide) | Swim University
Your spa is like a giant bathtub: regularly wiping down the surfaces is important to keep your hot tub clean. But eventually, the …
Can I use baking soda to clean my hot tub?
Baking soda is a mild abrasive cleaner that can be used to remove stubborn scum from hot tub shells. To use, mix baking soda with water to form a paste, apply it to the surface, scrub it gently with a soft cloth or sponge, and rinse thoroughly with water. Alternatively, apply a small amount of dry baking soda directly onto a damp sponge or cloth, scrub the affected area, and rinse thoroughly to remove all residue.
How do you clean a spa room?
Cleaning a steam room, hammam, or other tiled room is as simple as cleaning a bathroom. Regular soap and water can clean surfaces and remove germs, but to kill them, sanitize or disinfect all surfaces. The CDC recommends using cleaning products with at least 70 isopropyl alcohol. Disinfecting a sauna is similar to a steam room, using soapy water and hydrogen peroxide. For deep cleans, avoid commercial steam cleaners or pressure washers, as they can damage tile grout and remove the wood’s natural protective surface. Instead, use a domestic-quality, low-pressure steam cleaner to remove excess dirt and body oils before cleaning.
What do you clean the inside of a spa with?
409 is a popular selection for the removal of scum lines due to its degreasing properties. It is imperative to ensure that all acrylic areas, jets, water skimmer components, and the internal filter housing are thoroughly cleaned in order to facilitate the prompt and straightforward removal of scum.
How do you clean the inside of a spa cover?
To clean a hot tub cover, start by rinsing it with water to remove any chemicals on the underside. For tougher stains, use a cleaning solution like vinegar and water. Rinse and dry the cover again. For the vinyl side, follow the same cleaning method as the underside, but apply a small amount of UV protectant after it’s completely dry to prevent sun-bleaching and cracking. Visit a local hot tub store for a cover cleansing solution.
How to get rid of black mold in a hot tub?
Mold in a hot tub can be easily treated with a spa-friendly cleaning agent and a soft cloth. However, if mold is present, it may be deeper than visible and is likely in the pipes and jet system. To fix this, drain the water and refill with fresh water, using a pipe and jet cleaner to flush out and kill the mold. Consult your spa dealer to ensure the best cleaner for your spa model. After draining the water, wipe down the spa with a soft cloth and a spa-safe cleaner, rinse thoroughly, and drain any water that collects. Clean the filter, re-install it, and fill the tub with fresh water. To prevent mold in your hot tub, shock and clean the water correctly, using chlorine or bromine to maintain the correct levels.
How do you get rid of bacteria in a spa?
To maintain a bacteria-free hot tub, follow these steps:
- Test the water using a reliable test kit, pH test strip, or water sample to determine the best treatment.
- Clean and disinfect all surfaces, including interior, covers, filters, and jets, using a hot tub cleaner and rinsing.
- Replace or clean filters if bacteria growth clings to them. Clean them with a filter cleaner and rinse thoroughly.
- Repeat testing to ensure pH, alkalinity, and sanitizer levels are within acceptable range. Regular testing and monitoring of water chemistry are crucial for maintaining a bacteria-free hot tub.
By identifying and addressing any bacterial contamination, your spa can remain a clean and safe environment for relaxation and rejuvenation. Adherence to proper maintenance practices and collaboration with hot tub professionals is essential for maintaining your hot tub in its optimal condition.
Can I put vinegar in my hot tub?
To clean your hot tub without resorting to harsh chemicals, consider using natural and affordable cleaning agents. White vinegar is an effective and cost-effective solution for removing scum lines from the hot tub shell. Mix equal parts of vinegar and water in a spray bottle and spray onto the scum lines, allowing it to sit for a few minutes before scrubbing away the residue with a soft cloth or sponge.
However, vinegar is not recommended for cleaning hot tub pipes, as they are designed for this purpose. To ensure a clean and healthy hot tub, use a hot tub line flush product specifically designed for this purpose. Drain the hot tub and refill with fresh water after using vinegar.
How do you clean hot tub walls?
After draining your hot tub, clean the shell and jets with a damp cloth or tub scrubber. Avoid using regular household cleaning products as they are pH neutral and may damage the shell. Remove headrest cushions and wipe with warm water and a cloth. Clean the acrylic hot tub shell behind the pillows. Spray loose dirt or debris from the hot tub cover with a high-powered hose pipe and wipe the surface with a soft cloth. Finish with an approved hot tub cover cleaner.
How can I keep my spa clean without chemicals?
Non-chlorine shock is an oxidizer that removes contaminants from hot tub water, but it is not a sanitizer. Salt systems generate chlorine through electrolyzing salt, eliminating the need for traditional chlorine or bromine products. Ultraviolet (UV) systems use radiation to sanitize hot tub water, eliminating contaminants and reducing the amount of chlorine required. Mineral-based systems can reduce the amount of chlorine or other sanitizers needed to maintain hot tub water.
Ionizers release ions into the water to inhibit algae and bacteria growth, reducing the amount of sanitizer needed. Ozonators inject ozone into hot tub water to reduce the need for sanitizer and the frequency of shocking the hot tub. Enzyme-based treatment breaks down organic contaminants in the water, making it easier for sanitizers to work. Biguanide is a gentle sanitizer that can be used as an alternative to chlorine or bromine in hot tubs, but requires the use of non-bromine and non-chlorine-based shock.
Scale inhibitors prevent scale buildup in hot tub water, reducing the effectiveness of sanitizers. PH balancers help maintain proper PH levels in hot tub water, which is essential for the effectiveness of sanitizers.
Cost savings for low-chemical hot tub systems are possible, but it is important to carefully research and consider the benefits and drawbacks of each alternative before making a decision. It is also essential to understand the potential risks and consequences of using alternative substances on hot tub equipment and water quality. It is always best to consult a hot tub sanitation expert before making any changes to your hot tub maintenance routine to ensure the safety and effectiveness of your system.
📹 How to clean a hot tub the right way
In this video, I’m going to another customer maintenance job, but this time it’s to clean their hot tub. To start, the first step is to …
We have a scum line that is not visable but we can can feel it with our fingertips. When you suggest cleaning the scum line with white vinegar, are you suggesting that you would allow the white vinegar to mix with the hot tub water? Doesn’t seem it should be introduced into such a delicately balanced environment.
I am a commercial CPO. this is a very good example of regular maintenance on a residential level. this is an extremely thorough process, but definitely demonstrates an effective way to keep your hot tub absolutely spotless. However, it might be a tad Overkill. Simply draining the water on a regular basis should work Wonders on its own.
I need some advice. I have an above ground pool. I moved into my house and it was in bad shape when I moved here. I followed all of the directions to get it clean. Nothing was working. I ended up draining it and washed the liner and filled it back up following the directions again. It was finally clean. I kept up with maintenance. I was vacuuming 2x a week. And I still started getting algae on the pool wall/floor. So I added chemicals to kill it and vacuumed and scrubbed. Nothing was stopping it. It slowly turned green despite me following exact directions to stop the growth, kill the algae and vacuumed. All the leaves started falling and I couldn’t keep the leaves out fast enough. We have a lot of trees with large leaves in the yard above the pool. It was obvious I needed to start over AGAIN. I drained the water, cleaned out the leaves, sprayed it down and emptied again. Now what? Do I need a new liner? If not what do I clean it with? I can’t keep going through this process. I understand pools ARE hard work but I feel like this is beyond typical pool upkeep. Please help me!
My hot tub kept getting air in the second pump so half the jets were only working periodically but the other half were running regularly. When I turn the jets on high on the half that weren’t regularly ran I’m getting scum bubbles and a brown ring that is much more prominent on that side. Is there a chemical imbalance I could fix or do I just need to purge drain and start over?
I bought a used hot tub from someone and did all the hardwiring and electrical myself with the helo of some family members. City inspections are passed and now and the tub has been empty until now. It’s been 9 months now it’s been empty and the owner had it empty for about a year prior. Should I fill it up then use a shock treatment to purge out the drains and everything and then refill and add chemicals? All of the articles I’ve seen start with a hot tub filled and add chemicals.
This is the right way to clean a hot tub but an important step missed. You didn’t clean the internal pipes or pumps? That’s where all the gross stuff is, you have to pull the filters add a pipe and pump cleaner then run the tub for hours if you can 24 hours to get all the build up out of the plumbing system.
i personally dont use soap because of the suds. i suggest using a strong vinegar spray in a gardening bottle. a pond ready sump pump also works to help empty. non-phosphate poweder dish soap is good for soaking and spraying down filters in a five gal bucket, i just let them sit overnight to loosen debris thanks for the article very helpful.
Love perusal ya articles my guy! Can I ask what tester you use to check the cholorine/ph? And what filter cleaner do you use? Have you done any salt water tubs with one of those electrolysis chlorine generators? Was looking into it but they seem to be popular in the USA and not so much the UK :/ Expensive as hell. Keep up the epic work!
Hi, can you please help. we have a similar hot tub and we are trying to find out how to store it safely as we are not planning to use it for 6-8 months. Its winter and temperature is dropping to -7 degrees C, and will be dropping even lower. We have water in it at the moment and the water temp setting is 15 degrees, so we are wasting electricity if we are not using it. Some people suggest to always have water in the tub, but if the water freezes it may damage the unit. Any advise is greatly appreciated. Many thanks
Firstly I would be using a hot tub flush to clean all the bacteria beneath the system remove bio film and in clean internal pipe work, secondly I would be soaking the filter in filter cleaner in our estelle machine, I would be also using some waterline cleaner and also shocking the tub too 🤷♀️ you can also take out the jets on many tubs and clean them not quite sure why any of this wasn’t done ?
Dude, you confirmed my insecurities of not knowing how to properly clean a jacuzzi. First time owner, you showed things that confirmed what I was doing was right and you also showed me some nice tips to make my life easier and know that my kiddos can swim in a clean spa. It’d be nice if you could comment on the chemicals and how much chlorine and shock to use. I never know if I’m using too much or too little. Or also when is the right time to replace the filter versus just hosing it down. Great job though mate! I Hope to see more
Hi, thanks for your contribution. I have a smaller hot spa which I’m not using very often. I do switch it off for the winter by emptying it and cleaning it. However, when I switch it back on lots of (presumably) cal build up from the pipes…it looks disgusting and looks like bits of grated cheese. That only happens when I switch the pumps on after I refilled it with fresh water. As a result I need to start all over again. Such a waste of water. How do I avoid it ? As it seems I can never get the pipes fully clean when I switch it off for a period of time
Thank you mate. I just found your article how to clean and fill hot tub. I just bought an old home with a hot tub and never owned one. So, I try to search a article how to maintain it. Your article helps me a lot. Now I’m ready to clean and fill water in my hot tub. My teenage daughter bugs me to do it because she wants to use it. It is 49 deg F or 9.44 deg C outside in Washington, DC now. You sounds like Australian guy.
You forgot to flush out the pipes with a degreaser to clean the whole system before emptying the water bro! And in Aus we always have to increase the Alkalinity and ph from the tap water, as for the chlorine there shouldn’t be a reading from the tap water, the chlorine levels should dissipate in the hours after adding the chlorine which should be done daily to kill any bacteria and for ph/alkalinity should be tested and adjusted weekly.
Crappy Coast spa. I hate these tubs. Siphon with your hose and you don’t need the pump, will suck out leaves and debris without pump too. Don’t use detergent to wipe down spa fool. Well that was way more work than required. Clean the filter before the spa, silly! Oh yeah, still dirty water in pipes, pumps and filter housing. Coast spas can be a problem priming the pumps too. They rarely self prime like they should. Bleed the air out of the filter housing when the spa is refilled, housing will be full of air. pH was high from pool or detergent? What was your alkalinity before you adjusted pH?
Sorry but the title of your article should be how NOT to clean a hot tub. 1. You didn’t flush the lines with a biofilm remover 2. Filters should be soaked overnight in a cleaner 3. You shouldn’t use such high water pressure to clean the filter as it can damage and separate the fibers of the filter and make it less effective. 4. You should have checked the TA levels before the PH levels. 5. Bromine is a far more effective sanitiser for a hot tub. If you cleaned my tub like that, I’d make you do it again correctly.
Hello hope everyone is doing alright. Here is the story back in 1998 i have lost my right hand from the rest and injured my right leg the femur part i am lebanese living in lebanon at the moment but jusr feel like the wrong person in the wrong place. Like the lebanese gov. Doesnt really care about the 15% of the citizenc who has disability that live in the country instead of helping and giving them monthly benefits for example not $1000 but $500 at least they dont plus the law 220/2000 is not applied yet so I dont have rights to practice or enjoy like other disabiled people in other countries. I dont have my own apartment or place yet also am single and unable to have / be in a girlfriend boyfriend relationship. Also in lebanon there are 102 org’s. But half of them are not legal the other half are theifes and take advantage of the disabilied. But as the size of my country in my opinion Lebanon doesnt need 102 org. Its like they made it there job and all the money they recive or donations goes to there pockets to be spent on tbem selves and we get nothing from it. I have a feeling that those org. They dont want us to have a better future or get married one day also be indepandent. So they want us to always be at our knees and beg them for help .. anyway I hope this message gets to everyone also hope you guys could help me start an indepandant organization also keep intouch and help me build an 8 level building spaceilly made to house and support about 100 guy and girl with disability also employee 150 lebanese guys and girls and which the public can also benefit from not just the disabiled.