Dashboard lights in a vehicle can malfunction or cease to operate, posing a safety hazard. Common causes include blown fuses, burned out bulbs, and bad switches. To fix the issue, adjust the dial or knob to see if that fixes the problem. If the switch was accidentally bumped, the dashboard lights might have been turned off. Flip the switch or turn the dial or knob up to see if the lights come on or get brighter. If adjusting the switch doesn’t work, you may have a blown fuse or bad lightbulb.
The most common causes for car interior lights not working are blown fuses, burned out bulbs, and bad switches. To locate the problem, access the car’s fuse box and check the dimmer switch on the dashboard. If it is turned down or off, then check for a blown fuse or a broken lightbulb. The lights should start operating again.
Dashboard lights don’t fail often but can stop working due to a blown fuse, loose, or damaged wiring, or a faulty lightbulb. Troubleshooting can help eliminate electric ghosts meddling with your Lexus’ map lights. If the fuse feeding these circuits is still intact, the problem is most likely a wiring issue in a common feed wire near the fuse. If the dome light does not come on, the switch may be in the wrong position or there may be a problem with the vehicle.
To fix dashboard lights that won’t light, check and adjust the dimmer switch, check for a blown fuse, replace dashboard lightbulbs, and trace power from the fuse block. If a group of interior lights do not come on, check the wires at the suspect fuse block.
If the main fuse block hasn’t been cleaned, start by cleaning the main fuse block and trace power from the fuse block. If a jammed wire (pinched) is shorting to a high ground, it could explain the 20 holding. One of the original fuse panels had cracked and made the fuses on the cracked end a little loose.
📹 No Light in car dash? Top 4 things you can do to fix DIY
If you discover you have no lights on your car’s dashboard or dash and can no longer see the gauges at night, here are the top 4 …
Why won’t my dashboard lights turn on?
Dashboard lights can become non-functional due to various reasons, including a dimmer switch being turned off, a blown fuse, a bad lightbulb, electrical wiring, or other issues. While some problems can be fixed easily, a critical issue requires an experienced mechanic’s repair. To detect and fix non-functional dashboard lights, follow these steps:
- Turn on the ignition or put the key in the accessory position.
- Turn on the headlamps.
- Locate the dimmer switch for the lights.
- Try adjusting the dial or switch to see if that fixes the problem. If the issue persists, the vehicle should be taken to an experienced mechanic for repair.
Why are my car gauges not lighting up?
The instrument cluster may not function properly due to a bad fuse box, which powers the cluster. If the fuse box is not functioning properly, the cluster will also not work. To fix this, the fuse box needs to be replaced. It’s crucial to distinguish common causes from rare ones when experiencing vehicle problems to avoid wasting time and money on unnecessary repairs or causing more damage. Beck’s Auto Center in Lafayette, Indiana, has years of experience in fixing instrument clusters and has compiled five common reasons for the issue. One of the most common reasons is a blown fuse.
Why did the lights on my dashboard go off?
When your car’s electrical connection is interrupted, it can cause a range of issues, including the stereo, climate control, dashboard lights, and even the engine. This can indicate a critical fault in the vehicle’s electronics. It’s recommended to have any electrical issues checked out by trained professionals.
The first culprit to check is the battery. Ensure the battery is properly connected and that corrosion hasn’t interrupted its connection. Check the battery cables and terminals for a build-up of a whitish, powdery substance, which doesn’t conduct electricity. Enough corrosion on the battery terminals and cables can cause a bad electrical connection, leading to the dashboard lights going out. If the battery is dead and won’t hold a charge, it may need to be replaced.
If the battery holds a strong charge and has a solid connection, check the fuse box. If a main fuse has blown, the electronics may stop working altogether. Additionally, check for fusible links, which are special wires with built-in fuses that protect the car’s electronics from surges and ground faults. If one of these fusible links has blown, it’s necessary to replace it.
Why won t lights turn on?
If a bulb flickers on and off due to bad switch contacts, loose wire connections, or a light bulb socket, it is usually due to a loose wire connection at the switch itself. If the socket goes bad, it will need to be replaced. Recessed canister lights can also experience similar problems as ordinary ceiling light fixtures. They may suddenly turn off due to the safety features of recessed lights.
To fix this, check if the light bulbs have the correct wattage for the fixture, compare the wattage on the bulb with the rating on the light fixture, and install a lower-wattage bulb if necessary. If insulation is packed too tightly around the light fixture, it may trap heat around the canister, causing the limit switch to overheat and shut down the light fixture. Ensure enough air circulation around the canister to prevent overheating. If the light bulb wattage is correct and proper ventilation is present, consider replacing the limit switch or the entire light fixture.
Why is nothing on my dashboard working?
To fix car gauge and dashboard problems, locate the fuse associated with the instrument cluster and inspect it to determine if it has blown or needs replacement. Ensure that electricity is flowing through both sides of the fuse when turning the key in the ignition. Use a test light or multimeter to confirm this. If you don’t have the correct tools or don’t feel comfortable checking this yourself, take your car to a mechanic for a proper diagnostic.
If the fuse is in good condition, test if power is running to each instrument gauge. This may involve taking out the instrument cluster, which can be challenging and time-consuming depending on the vehicle type.
Why has my dashboard gone blank?
In order to diagnose and repair a malfunctioning automobile, it is first necessary to ascertain whether the issue lies with the fuse box or the battery connections. In the event that one lacks the requisite confidence to undertake troubleshooting, it is advisable to seek the guidance of a trusted mechanic or the dealer. In the event of malfunctioning dashboard lights and/or the car radio, it is advisable to seek the expertise of a reputable mechanic or dealer.
Why am I not getting power to my lights?
To troubleshoot a light bulb, first check if it has burned out and replace it if so. If the bulb is tight in the socket, tighten it by screwing it in tighter. If the metal socket tab has become flattened, bend it back slightly to make contact with the bulb. Check the connections at the switch and ensure power is off to the circuit. With the power shut off, check the wire connections at the light fixture and breaker panel. If concerns arise, consult a qualified electrician.
If the light bulb flickers, it usually means that the switch contacts are getting bad, which can be heard by a sizzling or crackling sound. Replace the switch if the switch contacts are bad. If the wire connections are loose, check the switch itself, the circuit breaker panel, or pass-through wire connections in the wall box or ceiling box. The most common problem is a loose wire connection at the switch, which is subject to constant on-off usage. Less commonly, a light bulb socket may go bad, requiring replacement.
Why is my headlight not showing up on my dashboard?
If your Chevy dashboard lights are dim, it’s possible that the headlights aren’t turned on, which can cause the issue. If the headlights aren’t turned on, check the dimmer switch to adjust the brightness of the dash lights. If the light levels are down, readjust it. If the dashboard is completely dark, the car might have blown a fuse, which can be fixed by replacing the old fuse. However, if the new fuse doesn’t last long, have it inspected at an authorized Chevrolet service center.
If only part of the instrument panel is dark, it’s likely that the dash is lit by individual LED lights. If one bulb burns out, the rest of the dashboard will remain lit. Replacing these bulbs can be challenging, so it’s best to consult a factory-authorized expert, such as Capitol Chevrolet in Salem, OR.
What does it mean when there is no lights on the dash?
The dashboard or ignition of a vehicle may not receive power due to a number of potential causes, including battery issues, blown fuses, ignition switch problems, faulty alternators, wiring issues, malfunctioning starters, low dimmer settings, and burned-out dash bulbs.
Why are my car interior lights not turning on?
When all car interior lights stop working simultaneously but other lights like the radio still work, it suggests a common issue with blown car fuses and fusible links. The fuse box may be located near the glove box, under the dashboard, or in the engine compartment. If your car has multiple fuse boxes, your owner’s manual can be helpful in locating the right one. If you cannot find the fuse, search the internet for a picture of the exact fuse box.
The “lights” fuse is usually the issue, but it can vary from vehicle to vehicle. To determine if a fuse is blown, use a multimeter or test light. If a multimeter shows no continuity between the terminals of a fuse, it indicates that it is blown. If you can’t find a wiring diagram for your specific make, model, and year, checking all fuses labeled “lights” is usually sufficient.
How do you reset dashboard lights?
To reset a check engine light, try turning off the car and restarting the engine, disconnecting the battery, and reconnecting it. If the light remains flashing, take your vehicle to a mechanic to avoid costly repairs. If the light doesn’t turn off or flashes, contact LK’s Auto Repair for diagnosis. Their ASE-Certified auto mechanics are highly trained to service and repair your vehicle. If you’re looking for an environmentally friendly alternative, LK’s Auto Repair in Bremerton, WA is an eco-friendly shop that cares about the community. Their location is 5921 St Hwy 303 NE 100 Bremerton, WA 98311. Call or schedule an appointment to learn more.
📹 Dash lights Do not Work Easy Common fixes
When the dashboard lights in your vehicle malfunction or cease to operate, the resulting effects can range from being a mere …
6 years later and this information is still useful! Rear-running lights did go out at the same time now that I think about it. However, I do have one question. Before finding this article, I had taken my cluster apart to check bulbs and voltage and found some current coming through the leads that go to the cluster lights. However, they didn’t work and I tried expanding the metal leads in case they weren’t making contact to no avail. I also checked each bulb individually (all still good) and saw no issue with the circuitry. Just wondering if the rear-running lights would cause the voltage to be too low for the cluster to turn on? I should mention they are on the same switch from factory.
My dash lights went out and I went to my car owners manual for help. After being more confused, couldn’t find a fuse link decided to goggle the fix. Came upon your article and ” woolah ” problem solved. Thanks for saving me time and headache. My rt tail light was burnt out, replaced bulb / fuse and dash lights worked. Thanks again
Hey Richard, great tutoring. I have a much older ambulance. Its a Renault Master T35 year 199something. mum was driving u a hill and noticed to row dash lights go out. Then the engine stalled and she stopped. The head lights work and the rest of the dash lights. Got to go help tomorrow. Any advice mate?
You are my hero. I just bought an Astro van with a good sticker, but no brake lights and also no dash lights. In the past, that has been the headlight switch. I bought another on, but no improvement. I also couldn’t find an blown fuses. So I took apart the taillight assembly and the bulbs still look OK. I decide to unscrew one and the glass part is just spinning. Went to the other side and same thing. I had to use pliers to get the bulbs out, but when replaced, everything was fixed. I spoke to other car guys and they didn’t know the dash lights can go out when you have a blown taillight (or two).
Hi Richard, this info is great. Just a question, my climate control, hvac, headlight switch and other lights do not go on(the switches do not light up at night) but also perusal this article i know that my number plate bulbs are out and should this be my problem as i haven’t had a chance to get around to the shop and change those bulbs.
Ford did a Light Control Module bypass due to a headlight failure. With in 2 weeks of the Ford bypass I loss my blinkers, Tail lights, panel lights, over head dome lights, the panic button on my key fob no longer triggers to horn for panic, when I lock the door the horn doesn’t beep anymore like it used to. Is it possible the bypass work is faulty causing this problem. They are telling me they did nothing to the LCM just bypass it. I know the bypass requires splicing and cuts into to specific wires. I also know the LCM does control everything I just mentioned but it seems hard to believe it not related since I didn’t have the problems before. Now the only thing that works is the headlights and my break lights. Everything else lighting wise does not. Whats your opinion. I go back to the dealer tomorrow to have them confirm what they did is still good.
Thanks for this info! I nearly didn’t watch the article after skipping through and not seeing any car parts visible. One of my Nissan Terranos probably has this very problem – it’s my old farm hack, so no biggie. The other Terrano – the road one – has no dash warning lights showing at ignition “on” position except the handbrake light. Any thoughts there? All the fuses in the kick panel are good. Alternator isn’t charging, if that gives any clues. Thanks.
i have a 1999 Camry v6… I changed the bulbs its working now but my dash lights still won’t go on. I blew about 6 fuses. I know it has something to do with the back end of my car because at night when the trunk is open and I close it, my back lights all of a sudden dont work. but if I close it a certain way it comes back on… what could be the problem…
I’m having issues with my dash lights not working. I’ve checked & replaced all of my exterior lamps to insure they are working properly. I have also replaced my headlight / dimmer controller and checked as many fuses as I could and still nothing. I can’t find a specific fuse for my dash lights. Where is it located? All of my other interior lights are working along with my radio lights. Any insight as to what I’m missing? 2004.5 GMC 2500HD 403 Duramax (LLY)
Thanks Richard on your good tip but my problem seems different. This is regarding my Cadillac Escalade ESV 2008. See if you can help. After my battery going weak due to long parking time, and a recent jump (That has not been very unusual in past but always with happy ending and uneventful, this time my car started but I noticed no dash backlight at all so I can’t see any speed or data but all four indicator levels are flashing blue constantly. I don’t see a failed lamp. I was told to disconnect battery over night that didn’t help either. Another suggested solution was to keep the key in the door and hold it for longer than 10 second and that was with no avail. Do you have any suggestions before I get it to the dealer that might ask for one of my kidneys to repair? Thanks man.
Yes the electrical gremlins coming from the taillights or taillight rail is a BMW from the 90s problem that migrated into all these World cars trying to be BMW E46s. I guess they hired engineers from BMW to help them build knockoffs and they brought their fine wiring harness skills with them. One bulb goes out and the whole string won’t light. Sounds like Christmas 1932.
This is great information. Most of us go down the wrong rabbit hole trying to figure out the problem. For weak daytime dash lights, which I have in my 12 year old Ford Expedition, I’m going to check the tail light bulbs and grounds for corrosion. On Fords, this is a fertile area in which to find the cause of problems when multiple MILs appear, odd DTCs, and apparently dim or non-functioning cluster illumination and other dash lights.Thanks again for this article. And, yes, I have already removed the cluster and reflowed every solder joint, and replaced the dimmer switch, but still can’t read the odometer or any other back-lit messages in daylight. At night, it works fine.
Hey Richard Ray, It’s great to see ya bro. All four tail and running lights went out. All fuses good. Then I noticed that the dash lights were out too. And then I noticed one of those pain in the wazoo low beams was out. AAAAARRGH! The Sky is Falling. OK the sky is all good. But I thought that my wire harness was attacking me from all angles. Thanks for the genius is simplicity type mellowing words of automobile wisdom oh great one. I should have tried changing the bulbs. I can go back to being lazy again. Whew!!! Many good things to you and yours.
what about Ford Flex 2014 my dash light go out going down the road then when turn dash light knob up the inside light come and dash light try come on have turn knob half way down get dash light working and inside lights still on about 20 minute they go off I am in wheel chair can help me as vet Thank you
So 4 weeks my dash light has been flickering on and off and then it’s fine now yesterday and went off the whole time I was driving then this morning it was off when I start the car then I start driving and it came back on I’m wondering if it’s a fuse if so it should be an easy fix right I just replace the fuse or like you said it might be a tail light or headlight but I haven’t checked to see if they go out I don’t believe they are out which makes me think that it possibly is the fuse but now you’re saying it could be a switch so I would like to fix it myself if it is an easy fix but I need to First figure out what is wrong with it in order to fix it
Thank you for the tip I thing some kind of light maybe loose cuz as I was reading all this comments my wife driving of course al out sudden we hit a bump. And boom 💥 dashboard lights came on lol 😂 thank you. Very much. I’m check that out I was already thinking about that mess it was going to cost me. PURO HERBALIFE ! !! PURE HERBALIFE HERE ALSO. YYEYAAAA
Hey Richard! My dumb ex put a new battery in wrong and reversed the polarity, alot got fried a DRL module, alternator, fuses etc. Dash lights wont turn on but all other lights are working. My wiper fuse pops as soon as I turn them on, I read a common issue is the rear motor so I disconnected that it still blew. If you have any ideas pleasw lmk
Instument panel is totally dark at night! One cause = On my 2013 Lexus RX, to the left of the steering column, there is a tiny light-bulb symbol with “down” arrow on one side and “up” arrow on opposite side. The arrows allow adjusting the brightness of the instrument panel lighting. It is totally dark at night (unless headlights are cut off) if the “down” arrow is all the way down. As you press the “up” or “down” arrow, an image comes onto the instrument panel to demo the degree of brightness. Someone may have turned them all the way down (deliberately or by mistake).
Thanks Richard I will check it out.Yes my tail lights don’t happen.I will get those globes replaced asp.Nice to meet meet you here from across the Atlantic in South Africa.I will consider this a free Christmas Gift from the US of A. See Yankies are still Good Folks just like the John Wayne Movies used to be.
what should i check for my 2010 cadillac CTS4. my instument control panel/gauge displays is totally black. no lights and no needle movement at all. also, on the dual climate control functions… only the passenger side is illuminated and you can adjust the temp. the driver side is blank. Any suggestions would be great. fuse, tail light. and fyi… my driver side head light (normal) is out. only the highbeam comes on – the driver side and not on the passenger. but the regular light comes on the passenger but not on the driver side. i paid the dealership $850 a couple of years ago to replace the instrument control panel. i don’t want to have to do that again. fingers crossed. please help/advise.
Hi L&R “XRays”. My Chevy Lumina 1996 dash lights are lost. I have checked all lights. All lights working ok. When light main switch is off radio lights are ok, but turning switch on…no dash lights and radio light goes off too. Main switch dimmer is not working, but when turning to the end it will light up interior light. I checked fuses too and the seem to be everything ok. Air conditioning is is only thing which is not working. Clutch in compressor is not working. But thats propably effect my dash light issue. -Rale
My 2000 ford expedition sun visor light don’t work, engine compartment light (under the hood) doesn’t work and rear wiper doesn’t work either. Noticed that all stopped working about the same time. Already replaced the wiper motor and still doesn’t work. Switched relays in fuse box in engine compartment and checked all fuses. Everything seems to be OK. Any thoughts
Okay. What if the dash lights don’t turn off at all?? They only turn off when my driver’s door is *open*. It is annoying as now I have to always leave my driver’s door slightly ajar so the lights inside don’t come on. Sometimes, though it randomly doesn’t do it. What does this mean?? I have thought about trying to get someone to just remove the fuse for the dash lights completely just so I don’t have them so I don’t constantly have to worry about a possible dead battery.
After installing an aftermarket radio, I’ve been looking for many solutions to fixing this problem after my dash lights and break lights went out for my 2006 Acura rsx while driving through a bump on the road. I really hope this solves my problem, if anyone has any suggestions on what to do, please let me know.
Is anyone’s headlights going out when their dash light and gauges go out and AC button and radio all go out at once I can turn the truck off and back on and they’ll come back on but then they’ll go out and then a few seconds or a few minutes it’s really wishy washy is it the ignition cuz I bypass the three wires going into the top of the ignition please help
I have a 2006 Chevy Cobalt. The dash lights work, but I notice when I start it not all the idiot lights come on, The bright light, parking brake and seatbelt lights come on but check engine, overhearing light etc… don’t come on. I’m worried I won’t know if I’m overheating( since there’s no temp gauge) or need to check engine for something. These are the ones that come on and go off after starting it. What do you think? Thanks
My dashboard light goes on but the speedometer or any of the needles are working… possible reason for this is that I was driving in the highway in a ver rainy day and the streets were flooded so much so that I’m sure some of the water might have caused some damage…. please anyone have any ideas ? Oh also I have a 2006 Chevy equinox
Super experienced mechanic replaced my ignition switch and that evening I noticed that the light over the engine temperature indicator was really faded. When I mentioned it to him he acted like he had no clue why and yet this YT guy indicated that with Chevy El Dorados there was a connection between the lights going out and the ignition switch. I found that fascinating. I have a Toyota Corolla. It’s been a month or so since that happened but now it’s completely faded out. I can still see it with the other part of the dash lit up but I wonder what’s causing it. Is there a connection to the ignition? I’m having a faulty starter as well because I bought a crap refurbished one from AutoZone. It’s literally been sketchy since it was first installed 2 years ago.
this dude has no clue what he is talking about. if he did he would be in a shop instead of an herbalife shop. people like this is why we have people come to my shop wanting things done without letting us diagnose the problem they are having. Then They get mad cause what they wanted done didn’t fix their problem. this is why ships charge, cause the training to work on cars is not free.
I have a 2009 Silverado. O e minute the Gage lights are fine. I park and then i go to start the truck and they dont work. Just started doin it. I checked my lights like u said ut all good . Any suggestions. Im hoping it not the $80.00 switch. Thank for your time. And how the hell you loose alll that wait?.
I have a 05 Hyundai Elantra and on my way home the other night the dash lights went off. I continued to get to the house and when I arrived, I did in fact have a passenger taillight out. Today I replaced the taillight and the dash lights arent on still. Checked the fuse and its fine. Not sure what to do now. Any help would be greatly appreciated.
I have a 2003 Dodge Durango, I have an after market radio that was hanging out a little bit so I forced it in causing the radio to stop working, the next day I realized the dash lights aren’t working for the speedometer and the green lights around the ac aswell, I tested all fuses and they all have power to them, anyone know the issue?
I reset my pcn in my 2004 Kia Rio Code p0731 power train Removed ground. Cable Turned lights on to power down pcn didn’t shut lights off before reconnecting ground Started up when through the shift ranges drive to 1. I noticed I have no gauge lights Took dash out replaced the for 194 bulbs for gauges Put back plugs Turned key put light on No gauge lights.
Thank you so much I couldn’t figure out why my dashboard light went out for no reason out of the blue one day while I was driving. I was trying to Google it trying to find out why checked everything everything was good battery was good fuses were good. and then I watched your article and it told me to check my lights which I did and which I did have one that was out I really appreciate you thank you so much you really put me at ease. I was very stressed out about how much money it was going to cost me to get my car fixed so thank you.
Richard, I have been having issues with my 2005 Dodge Ram. The gauges light up but none of the warning or informational lights light up. The odometer, gear selection indicator, high beam indicators and even the turn signal indicators wont light up. All lights and turn signals work outside the truck. I did the instrument cluster diagnostic test and the gauges did the sweeps but no lights or codes came up in the odometer area. Any idea? Thanks
hey Richard I have a 03 gmc Sonoma extended cab 4.3. my issue with my truck is no dash lights unless I almost click it up to turn the interior lights on but other than that I can’t dim or brighten the dash lights at all. brake lights are fine. at night when my headlights are on they flicker as well of the interior light. I’ve already tested the battery and alternator with my digital multimeter and they are in specs. I’m pretty sure I need to get a new headlight switch just wanted someone else’s opinion before I go spend 50 bucks on this part
hello buddy. Joe here all the way from England. I have a Nissan primera 4 door saloon year 1998.I had a original nissan primera tape deck radio with code etc. I had a audio guy install a CD player with aux connectivity, a 1200 amp and sub woofer. before he installed it I had tail lights,dash lights and a fog light and dipped and sidelights. I now have only indicators, full head lights (front) and full beam and no tail light or dash lights. I’ve changed the tail light amp and still have no tail lights. could it be a wire that has tripped or the earth wire that has been put on a bolt in the bonnet
I just had my car detailed today, and much to my surprise, while running errands, I noticed that the dashboard completely goes dark when I turn on the headlights. My blood pressure. Could something have happened during the detail. I can’t chase the guy. I just will never use him again. I need this fixed pronto, as I will be driving in the evening!! HELPPPP
On a Lincoln Town Car (later models), there’s usually two bulbs in each tail light. If one goes out, the turn signal on that side now operates at twice the speed. That’s your clue there’s a bulb out. The cluster display on my 06 TC is on the fritz, sometimes displays partial, flickers like crazy, or doesn’t work at all (while speedo, tach, fuel and engine temp work fine). I hope there’s an easy fix, not looking forward to pulling the dash.
Richard: Can you help me? I was cleaning my battery terminals and accidently shorted the positive to ground. Now my Dash lights are not working. 2006 Chevy Colorado LS I couldn’t get the nut on under terminal clamp and used a forceps to hold the nut and accidently hit metal and shorted out. Everything else seems to be working. Truck runs good. Do you think I fried something?
interesting, wonder if that’s my issue with a 97 centra Trunk/door light stay on all the time along with the coolant light but, coolent is fine and my gear shift indicator in the dash the light is, but, I do have a iossue with driver side parking light not coming on, ill check bulb, every thing else is fine I just like to keep thinks working like they should… ty for this
Did the walk around…rear light was out..went inside came out light was on? This morning no lights, only head light! Check fuse..one is out for park lights..replace, and it keeps blowing instantly..no dash no running light no rear lights..blinkers work, headlights work..running lights, brake lights, dash all out! Any ideas?
my 2005 prius keeps doing this so i took it to a hybrid mechanic and they said a lot of the priuses came with a factory defect that turns the dash board lights off and to replace the speedometer which solves the issue would be $324. While this may sound like a lot, another place wanted to charge me $850
So I got a good 1 for you I bought a 03 Chevrolet malibu no key so I bought a new ignition switch and the ignition to go with put it all in turn it to start it does nothing not abs light no battery light no sign of life but the turn signals work why it’s in the on position and all that but no warning lights and no start
I have a 06 Hyundai sonata kids had drink in the car and some of the drink spilled over into the gear shift and now my dash lights my automatic headlights will not come on i have to use the daytime lights my windows won’t roll down, my tail lights doesn’t work and my dash lights are out i also can’t pop the trunk from the inside. What could be done to fix it.