How Short Of A Door Can I Order?

When ordering a prehung exterior door that is shorter than normal, it is usually easiest to order it from the lumberyard. However, it is possible to shorten the unit yourself, as manufacturers typically allow wood doors to be trimmed by 1⁄2 in. at the top and 1-1⁄2 in. at the bottom. Our doors come in all shapes and sizes, up to 12 feet tall, 6 feet wide, and 2-1/4″ thick. We offer a variety of textured and obscure glass options to fit your personality.

Standard exterior doors are 3 ft. 0 in. wide, although side doors may be 2 ft. 8 in. or 2 ft. 10 in. wide. Extra-wide 42-in. exterior doors can be special-ordered, but their greater weight requires larger hinges. In this video, carpenter and former senior editor Andy Engel shows how to disassemble a prehung exterior door, measure and cut the door slab to fit an existing opening, and shorten the jamb to match.

US Door and More Inc. offers a wide range of exterior and custom doors, including those that conform to industry-wide standard exterior door sizes. For shorter than 80″ exterior doors, custom height doors can be ordered from millwork supply places or Lowes, but it takes time to cut them down and depends on the required dimensions.

Custom-made exterior doors take six to eight weeks to fulfill, depending on the complexity of the order. Standard sizes for front doors include widths of 3′ or 3′ 6″ and heights of 6′ 8″ or 8′. Delivery times depend on the complexity of the order, but custom-made doors generally take six to eight weeks to fulfill.

Can you get shorter doors?

Can you Trim Laminate Doors?. Yes, you can, and you can trim all of the edges (top, bottom and sides) without worrying about splintering or cracking. However, laminate doors are the most unyielding out of the three. You can only trim up to 5mm, any more than that and you risk damaging the integrity of the door.

How do you Seal a Door After Cutting it?. We mentioned ‘finishing’ the door in step four of this guide. This isn’t just for aesthetic purposes. Finishing, either by treating or painting the wood adds a protective layer. You won’t have to worry about moisture seeping into and wear and tear will take longer to become a problem.

• Oils: Choose from clear, matt or satin.
• Finishes: Shades include dark, medium, light and clear.
• Stain or varnish: These are available in a considerable range of colours.
• Paints: Similar to stains or varnish, these come in a variety of colours and can have a gloss or matt finish.

Can you get a short door?

Short doors, which are interior doors shorter than standard ones, come in various types and materials, allowing for customization to suit any space. Selecting the right style and hardware is crucial for adding aesthetic appeal to your home. Regular cleaning and maintenance are essential for protecting short door longevity. Types include P rehung doors, S lab doors, glass barn doors, and French doors.

How much can I shorten a door?

Hollow-core doors have a strong outer frame, making them suitable for trimming. However, it’s important not to cut too much away, as this could damage the door’s structural integrity and require replacement. It’s generally recommended to trim no more than a quarter-inch off the sides. It’s crucial to consult the manufacturer or product finishing instructions to avoid damaging the door. Oak veneer doors have lippings made from solid wood, allowing only about 10mm of trimming.

Accurate measurements are essential when ordering this material. Laminate doors can be trimmed, but they are the most unyielding, with a maximum trim of 5mm. Trimming more than this could damage the door’s integrity. Therefore, it’s essential to choose the right door for your needs.

Can doors be cut down to size?

Trimming down interior doors, including hollow core doors, is possible and often necessary to achieve the desired fit. While there is no standard legislation for door size, many brands adhere to a set of common sizes. It is crucial to take precise measurements and purchase a door that is as close to true as possible. Minor adjustments may be necessary due to varying frames, rough openings, and floor coverings. While it is possible to shorten a new door to fit into an old frame, it is important not to cut away too much material.

If your frame is close to standard, it may be easier to buy a pre-finished door and trim the sides, top, and bottom down to fit perfectly. The parts need to be touched up with the same stain or paint color, but the project is relatively easy.

What is the smallest door size allowed?

It is imperative that each door opening have a minimum width of 32 inches (813 mm) to ensure the accommodation of the occupant load and the provision of a clear view.

Can you cut 2 inches off a door?

Trimming off a hollow core door can be done to accommodate thicker carpet, misread tape measure, or wonky doorframe. However, cutting off over 2 inches can cause the door’s edge to become non-solid. It’s not always advisable to trim hollow core doors for serious alterations. If unsure about trimming allowances, consult your supplier. If too much is cut off, the door’s structural integrity can be compromised, which can be fixed by reinserting a block from the bottom of the door inside the veneer using glue.

How short can an exterior door be?

A standard exterior door size is not an average due to the variety of homes and entryways. In American houses, the most common front door size is 36 inches wide by 80 inches tall, and almost 2 inches thick. However, doors can be as narrow as 30 inches and as tall as 96 inches, and thickness depends on the door material. Entry doors come in single- and double-door configurations, with additional options like matching sidelights and transoms affecting the overall size. Pella entry doors come in a wide range of standard and custom sizes to fit your needs.

What is the smallest exterior door you can buy?

Standard exterior doors typically have a width of 36 inches, with smaller options available in 30 or 32 inch widths. They must have a minimum height of 80 inches, with custom doors potentially reaching up to 96 inches. Sliding glass doors have a standard height, but their width can vary depending on the location and opening size. Builders often create standard door frame areas to make replacements easier to find. Overall, exterior doors can be larger or smaller than interior ones, with custom doors available in even higher sizes.

Can you buy shorter exterior doors?

It is possible to order custom entry exterior doors in the desired size and subsequently install them oneself, having first selected the optimal option.

What is the shortest door you can buy?

Passage doors must have a minimum height of 80 inches, with standard width sizes for interior doors being 24″, 28, 30, 32″, and 36. The minimum recommended door width for persons with disabilities is 36 inches. The standard thickness for an interior door is 1 3/8, but if the door exceeds 36″ or is over 90″, it should be 1 3/4 inches thick. Utility and closet doors typically have tighter passages than standard doors, with doors built before the 1990s having narrow passages of 18 inches.

Newer doors typically have a width of 30 inches and a standard high of 96 inches. To replace a door, measure it from top to bottom, left to right, and thickness, with most doors having a thickness of 1 ¾ inch. Measure the width of the door jamb and the height and width of the frame, not including the trim. A rough-in measurement should be added to the door’s width and height, regardless of whether it is a pre-hung door.

Can you make an exterior door shorter?

When ordering a shorter prehung exterior door, it is typically easiest to order from a lumberyard. However, it is possible to shorten the unit yourself, typically allowing wood doors to be trimmed by 1⁄2 in. at the top and 1-1⁄2 in. at the bottom. To do this, disassemble the unit, remove the door from its frame, place it on a surface that won’t scratch the door, and remove the door-bottom weatherstripping.

Mark the cut on each edge of the door and clamp a shooting board to the door, positioning the clamps with their long ends down to avoid interference with the saw. Place a block under each clamp to protect the other side of the door.