To replace a broken bathroom mirror, follow these steps:
- Place masking tape over the broken mirror in the shape of an “X” over it.
- Remove the cabinet door to access the mirror.
- Remove the mirror by removing the framing.
- Measure for a new mirror and install it.
- Install the new mirror by following the step-by-step guide and taking necessary safety precautions.
Removing a bathroom mirror from a wall is a simple and easy DIY project that can transform the look of any bathroom. However, it is best done as a two-person project, as you run a higher risk of safety issues like broken glass.
To remove a mirror glued to tile, tap the mirror well and try heating the adhesive to loosen it. Slip the wire between the mirror and wall at one of the top corners of the mirror and move the wire diagonally toward the center until you meet the mirror.
Start with the hinged side first and gently work the mirror, backing board, and silicone seal into the hinged frame piece. Wipe the wall down before applying glue, let it dry, and ensure the mirror is perfectly plumb or slightly leaning back.
After removing the mirror from the wall, clean the surface thoroughly and check the mounting hardware and screws to ensure they are still secure. This process can be completed in just minutes and can be a cost-effective and efficient way to update your bathroom mirror.
📹 How To Remove A Glass Bathroom Mirror Safely
How to remove a glass bathroom mirror. Shop Jeff’s favorite tools and great products and help support our next project! ▻ Shop …
📹 Easy way to safely remove a mirror glued to the wall
I’ll show you the easy way to safely remove a glued on mirror from the wall. Easily remove your bathroom vanity mirror. No special …
Thank you for this article. The clip issue was bothering me. I am doing my elderly mothers bathroom over this weekend and I was scratching my head on the clips. QQ: if there is a lot of glue on back of the mirror, how would I repair the drywall? Please, please, please don’t tell me that i have to replace it!
I love your articles! I have a strange situation with my bathroom wall. There is tile over drywall. They removed the mirror section of the tile to place a cheap 5 part mirror in the recessed area. The problem is drywall doesn’t come in the thickness of tile. Any suggestions for filling that gap once the mirror is removed? Thanks!
I used to look at you like a superman on home renovation until I watched this article. No Safety (common sense) were used here in this article, but the gloves. No glasses, no long leaves shirt, NO TAPE used on the mirror in case it brakes!! You know there are people who doesn’t use common sense at all. The only article i didn’t like from you just because you didn’t use your common sense. So sad!
WOW! Just what I needed! I’m so glad you made this article. Exactly what I had. Now, why did I remove it? I had a new roof installed. I have a rambler. The roofers made so many loud drops and bangs I thought they were going to fall through the roof. My vanity and mirror were pulled away from the wall – I take from the house shaking. I was afraid the mirror was going to fall and break. They also added a nice crack above a doorway in another room and messed up the molding around a pocket door. The clips were exactly how it was installed. Thank goodness no glue! I was thinking of using a rubber mallet and “hammering” it back in place, repaint and replace mirror. Thanks.
The mirror we removed was much smaller but the previous owner must have used an entire tube of some sort of construction cement to attach it to the drywall. They were going for a “window” look because there are no windows in the bathroom and just put cheap shutters over it. Couldn’t open the shutters and couldn’t see the mirror. Not sure what they were thinking. We managed to remove it (and chunks of drywall) by using packing tape over the entire thing and using a prybar. What a nightmare.
Watched this article this morning before removing a similar size mirror. So glad I did as everything detailed happened – especially the pealing sound as the adhesive comes away from the plasterboard (dryboard) paper. This definitely saved me making a terrible mess and probably a hospital trip so thank you!
Wearing long sleeves and a face shield would be a good idea…you only need it to let go suddenly and it slip down to hit the vanity or hit on the corner and you’d have shards and splinters flying. Also, as someone else said, tape the mirror surface in close grid pattern to minimize the shatter if it does break. Never hurts to be prepared for the worst….
I just came back to thank you for uploading this article. I had a heavy thick mirror stuck to the wall with a ridiculous amount of gorilla. Plus it was off centre, which constantly annoyed the hell out of me. Watched your article, bought a pack of wedges from ebay (really quite cheap). Followed your instructions, took little breaks, didn’t rush it. The mirror came away from the wall like a dream. The mirror was 50s bevelled so really glad I didn’t have to break it, I also gave mine away like the guy below. So you saved two mirrors. Again, thank you, from the UK.
Once I get it off do I need to glue my new mirror on? Do you have a mirror install article? Thanks for this removal article. It was very helpful! I hope to install a new mirror in my bathroom soon. I already have the mirror and I want to get it up before my wild, rambunctious, and clumsy household breaks it. 😂
We have a bathroom wall with 5 mirrors stacked on top of each other that reach the ceiling. These are glued on to plasterboard. The ‘expert’ who fitted the bathroom flooring, in his haste, broke the bottom mirror. I’ve ordered a same size bottom mirror but am unsure how to get the broken one off without the top edge of the broken mirror grinding and maybe chipping the one above it. Any ideas please?
We watched your article and did this and it worked PERFECTLY! We didn’t even need a hammer. We just kept sliding the shims in until it popped. We did not hear any tearing but I think that’s because there was only one big spot of adhesion. We located the big spot of adhesion after shimming all the sides and were able to focus the shimming around that spot. It came off perfectly clean. Thank you!
Seeing this was actually really helpful to me, as someone about to install one about the same size. Answered my “how much adhesive is too much?” question. I don’t want a future renovation/change of mind to require breaking the mirror. I can see this amount of adhesive or even a little less looks like just the right amount. Thanks!