Phil provides a comprehensive DIY guide on repairing and maintaining mobile home exterior door hinges, ensuring smooth operation and enhanced security. Common issues include squeaking, sticking, misalignment, and loose screws. To fix these problems, clean the door and frame, as dirt and debris can cause a door to stick.
To fix noisy hinges, broken doorknobs, and sticking doors, follow these steps:
Check the hinges: If the screws are loose, tighten them. If the hinge is part of the door frame, replace it or the entire door. If the hinge is loose, use thin cardboard or wooden shims between the hinges and the door frame to realign the door.
Install the hinge: Remove the rod, reinsert it through nylon grommets, and re-weld the rod to maintain the door’s integrity. This can be a laborious job, but it is a quick and easy fix for making the mobile home feel more home-like.
Remove the doorknob and any other hardware that can be used again in the future. Start unscrewing the hinges while the door is open. This will help make the place feel more home-like and prevent the need for a new door.
📹 How to Fix Hinges on Mobile Home Exterior Door
June 3, 2021; Homosassa, Florida: Nice cheap easy fix for hinges gone bad on an exterior Mobile home door. ADS ARE NOT …
How to fix hinge-bound door hinges?
To remove a hinge bind, start by removing the top hinge and adding a shim between the hinge leaf and the frame. Smaller shims should be used in this application. Then, add shims between the hinge and hinge reinforcement to push the door away from the rabbet and eliminate the bind. Hinge bind occurs when the hinge edge of the door closest to the hinge barrel hits the frame’s rabbet, preventing proper door opening or closing. To eliminate hinge bind, open the door, place a support or wooden wedge under it, and remove the top hinge and add a steel shim between the hinge leaf and the door or frame.
How to repair door hinges?
Loose door hinges can cause sagging doors due to screws that don’t bite into the door jamb. To fix this issue, remove the loose screws, coat a wooden golf tee with glue, tap the tee into the hinge screw hole with a hammer, score the tee flush with the mortise, break the tee off even with the bottom of the mortise, allow the glue to dry, and reinstall the hinge and screws in the holes. Today’s Homeowner aims to help homeowners maintain or improve their homes safely and effectively, adhering to strict editorial standards and carefully veting the advice and resources referenced in their articles.
How to fix exterior door sagging?
To fix a sagging door, tighten the screws on both sides of the hinge, starting with the top hinge. Remove hinge spacers, also known as hinge shims, to adjust door alignment during installation. Add new hinge screws and remove excess paint or stain. Common causes of sagging doors include loose hinges, a spacer added to the top hinge, loose hinge screws, and additional coats of paint or stain. This simple fix can prevent the door from scraping or getting stuck, and can be done without replacing the door or hiring a professional.
How to install exterior door hinges?
This guide explains how to install door hinges on door blanks or slabs, a popular choice for their wider design options. The process involves mortising, which involves sinking the hinges flush and ensuring proper door opening and closing. The hinge should be mortised or recessed into the door so that the top surface is flush with the door. This gives a tighter fit and more strength to the door and hinge.
The guide also explains the steps to establish the work area, cut the outline with a knife, sharpen the chisel, mortise the hinge, check the hinge depth, and finally, install the hinges. The guide emphasizes the importance of proper care and patience in this process.
How do you secure external door hinges?
Safety studs or pegs are a secure option for hinges, providing a secure hold even if the hinge pin is removed. They can be installed in one of the holes on the hinge leaves, ensuring the door cannot be taken off its hinges. If the screw-holes don’t align, drilling a matching hole and placing a screw without a head or a short, thick nail into one of the screw-holes can engage the opposite leaf. Safety studs are a good security measure for those who still need to remove their door but don’t want to spend time and effort unscrewing its hinges.
To ensure the security of your door hinges, it’s recommended to consult a locksmith or security contractor before making any adjustments or retrofits. They can assess your hinges and make professional recommendations to keep your doorways secure. While secure door hinges may reduce the likelihood of intruders, they may help reduce the likelihood of intruders. If renting an apartment, consult with your landlord about securing your hinges and any other improvements you wish to make.
How to fix a sagging mobile home storm door?
To reduce wear and tear and correct sag in a screen door, remove the bottom hinge, clear debris, and lay a wooden shim or cardboard strip by the hinge. Replace all screws and double-check alignment by opening and shutting the door repeatedly.
A screen door turnbuckle acts as a bracing, strengthening the door by connecting to a coupling nut. Place the turnbuckle squarely on the door’s bottom corner, diagonally below the opening side and up to the hinge side. Open and shut the door to ensure the turnbuckle doesn’t impede the door seal. Mark the screw holes with a pencil, drill the screws, tighten them, close and open the door again, and tighten the screws to secure the turnbuckle.
Hold the coupling nut on the turnbuckle and watch as the rods raise the drooping side of the door. Turn the nut until the door is flush with the floor. If the turnbuckle becomes too tight, loosen it accordingly.
Can you fix the hinge on a storm door?
To repair a broken storm door hinge, measure the area where the new hinge will be installed and find a hinge that matches the old one. Screw the replacement hinge components into the wall and door where the broken one was removed. Use storm door hinges like Screen Door Spring Hinges from Hinge Outlet. Place the door on the hinges, level it to ensure proper opening and closing, and secure the hinge pins with a screwdriver. This successfully repaired the broken hinge, ensuring smooth and secure opening and closing. Storm doors offer various functional benefits, so it’s important to take care of them.
How do you make hinges stay in place?
To fix squeaking and creaking doors, use a screwdriver or power drill to tighten screws in hinge plates attached to the door and frame. Start with the top hinge, then middle, and bottom hinges. Tighten all screws in both the door and frame. If the screws holding the hinges have worked loose over time, the wood around the hinge can compress, creating extra space for the hinge to move. To assess the damage, gently push the door to feel the play. If the door rattles or shifts over an inch, the hinges are likely worn out or broken and need replacement. If the screws have just come loose from the frame and door, this is an easy DIY fix.
What is the correct way for door hinges?
To hang door hinges correctly, align them with the hinge mortises on the door frame and secure them using screws. Ensure they are level and the door swings smoothly. Double-check alignment and test the door’s movement before installing hinge pins. Hinges are installed on the door frame, with hinge recesses chiseled into the frame and screws securely attached. Once securely in place, align and attach the door to the hinges. Hinges are installed inside the door, making them invisible from the outside. The hinge pins may be visible on the inside or outside depending on the design.
Should hinges be on the outside of exterior door?
Exterior doors are crucial for ensuring safety and security, especially in hurricane-prone areas like Louisiana. The hinges that hold the door in place are typically located inside the house. However, in areas like Louisiana, some doors swing out for safety reasons, requiring the hinges to be outside. If these doors are not properly secured, an intruder can easily remove the door, even if it’s locked.
To make the situation safer, consider purchasing safety hinges with non-removable pins from hardware stores or locksmiths, retrofitting security locks onto existing hinges to make them tamper-proof, or seeking help. Although installing hinges can be challenging, the effort is worth it as it is a significant security measure.
How to fix door hinges that won’t close?
In order to rectify a door that is unable to remain securely closed, it is necessary to tighten any loose screws, adjust the strike plate, utilise shims between the hinges and frame, or replace the hinge pins with longer ones. Should the issue persist, it is advisable to seek the assistance of a qualified professional.
📹 DON’T BUY IT, FIX IT!!! Mobile Home Door Repair
ABOUT US We are renovating our 1988 Palm Harbor single wide mobile home paycheck to paycheck debt free and as we …
I have been searching, researching and looking for a few days now (on and off) tryna figure out how to adjust the door on our place. I’d never seen these kind of hinges before so I had to figure out what they were called first! You were the first, and so far the only, article about the correct hinges. I am confident that I can get it done now! Thank you!!
I am missing the long rod 😭😭 I know you said that you had initially thought that the rod was length of the door, then said that it’s not…. but I’m pretty sure that on the day I was finally pissed enough with my back door not closing I had to pull out the rod. It was hanging out the bottom…and after I pulled that long sucker out the door just fell right on off. 😅😕🥺😰 Anyways… sooo The rod is a 1/4 in Diameter (98% sure) but can’t find one for the length of the door… what else can I do? My last resort will be to buy a (cheaper) “normal house door” and just cut up ⬆️ into towards the ceiling and ‘make it fit’.
Did you think about small C-clips? I know the washers would be more reliable though! My hinges are over extended. I’m not sure how to go about bending them back without removing them? If I have to do all that I’ll just get a door! You are correct though, mobile home repair sucks! They’re not concerned at all about the person that might have to fix something on them. I’ve almost finished remodeling my whole double wide, and MAN!!!!, I wish I could talk to the guys who had the staple guns and nailers!
My pins are gone completely lol…not funny What I’m doin is trying to make a new pin from a stainless grill warming rack and I put the new pin in hinge and heated with torch and hammered until pin was tight inside the hinge part that goes on door….now im having issue with getting pin in the other part thats on frame and it’s not easy or fun
I live in a 2007 Clayton14’x80′ mobile home. We purchased it in 2011 from the original owner and had it moved onto out 2 acres “homestead”. We did a complete updating in 2011 but now that my woodworking/ cnc shop is completed we are starting to get ideas for new projects. Thanks for the inspiration!!
Thats funny you just showed this. We ordered a new storm door and I had to remove the original. I had to pull the storm door off the trailer with a tow strap because it wouldn’t come off. They used 20 lbs of caulk to hold that sucker on, then they used a million screws to fasten it to the frame of the house. I removed all of those, then used a sharpened putty knife and a hammer to cut the caulk. Still couldn’t remove it. So I pulled it off with our Subaru and a tow strap. The article is funny. I of course now have to build out a normal wooden frame around the door in order to mount the new storm door to it. Lumber is EXPENCIVE. Cost me $77 for 3 2×4’s and 3- 2x1x8. ouch! Then I forgot the nails and had to go back.
Oh Sam you just crack me up, I could imagine yours or somebody else’s kids doing that! My niece that is 25 years old and she slams my door like that too. I’m like dang you don’t have to slam the door so hard you just shook the whole house! I thought for sure Angela was going to throw herself into the house like you did lol!
It is amazing how sometimes, it’s the seemingly small things that can lower the quality of life and in your case, feeling traumatized out of a relaxed calm state. It can take it’s toll on us if we let it. You two help people alot with things that can seem simple, but they keep putting it off because they simply do not have the know-how. You are a good example on pursuing in getting something done that needs to be done. Also, a good example of a married couple working well together for the benefit of each other and that of their family unit.
Our house was built in 2016. Our back door was identical to yours with one exception. The door was 1/2 the quality of that one. Same exact design but our dogs warped the door in the first year we moved in. I replaced with a better quality door earlier this year. And for anyone reading this… You have to special order the door because NONE of the local “box stores” carry any exterior open doors.
We had a tornado & thunderstorm that shook the MH worse than earthquakes I experienced in California & Alaska. Now, the front door is off by 1/2 inch and won’t close. Plus a loud creaking floor board area in front of the door. It’s now June 2024, the MH is a 2024. But our door doesn’t have screws like that. It’s like a site-built-home’s door.
After perusal your great and entertaining article, I temporarily fixed my door that sagged. It would not stay closed. I found 3 small nylon washers in my parts cabinet and that’s all it took. Did not have to remove the door. I cut a small V-shaped notch in the washers and then snapped a washer over the pin on the bottom of each hinge. No more sag. The only tools required were a razor knife to cut a tiny V-notch out of each of the 3 washers. Long-nose pliers to grab the washer and snap it into place over the pin. A shovel handle that I used for leverage under the door to raise it far enough to insert a nylon washer. I tried to make a article, but it would never be as good as yours, so I erased it. :face-blue-smiling:
I loved your article. Thank you for sharing. We have a manufactured home and the front door started peeling. Its hard to scrape thr remainder off. Any suggestions to how to get the plastic/paint off? It gets REALLY hot since its had of metal. So, what would you replace that plasic with to protect the door? Any suggestions would be crazy helpful. Thank you in advance!
A nice door repair project. Others would have replaced it. You saved money and solved the issue. It would be really cool to see a front covered porch deck and back covered porch deck. That would add some nice outdoor living space for entertaining and enjoying the view. Have you thought of putting metal roofing on the house as siding? Its been one hot and dry Summer 2021. Blessings beautiful family.
My kids slam my door like this and it doesn’t latch.. I think the door itself is bent too its been like that since I bought the house. Should I try to replace the hinges and see if that helps? Also the weatherstripping seals around the door are completely shot, weatherstripping I bought helps but isn’t great. I think I just need a whole new door😢
Great timing guys! Our daughter has been complaining about the back door on the mobile over at the other place not closing and having to be very FIRM to close it to make sure it’s latched. I’ll bet it’s the same problem. I’m gonna have the hubs watch this when he gets a minute. I mean, he’s already gonna be over there ripping up the floor to reinforce the joist, taking out the old tub, toilet, and vanity, installing a new floor, putting down vinyl, installing a new shower, toilet and vanity …..what’s one more thing? Right?
Ya’ll make it look so simple. I have all the tools ever made and I just know I would end up with no door at all and using a tarp haha When I step back and look at my doors I swear the whole shabang was manufactured lemon crooked. I have two front doors and both are sagging that way. Cute article and informative. It’s too bad that where I am parts are nowhere to be seen( even online for my model). The house isn’t even that old. I’ve been at my wit’s end with all the odd measurements and odd size screws and bolts. Every stupid screw in here has stripped the second it sees the driver. If I try this and it goes wrong imma need ya’ll to come fix it 🙂 Loved the article and your roof!
My storm door and inswinging exterior door were badly damaged in a hail storm. Is there a way to raise the header to allow a regular exterior door that I can buy at a big box store ( much cheaper) than a mobile home door? I’d like to get rid of the storm door and go with just a good exterior door. Thanks for your excellent articles!
Has it been out before? I saw holes in the metal frame at the latch. Just saw how you had to destroy the frame corners. Could you have drilled it out or just cut off enough to get the hinge pin out? Might have been able to resleeve those hinges. The place you got the hinges from also has a white storm door hinge pin kit.
At 4:52 The scenery behind you looks so much like Fleming county, Kentucky, and in another article, that’s where I thought you might live, Until you mentioned in another article that you live in western North Carolina! I used to travel I-40 often when I was a younger man driving the big truck, so I never got to absorb the beauty of that area much, having to focus on the road! I sure would like, if you kidz would take some footage of your area, say maybe if you are going out to get supplies, etc.! I don’t get out much these days in my older years being crippled up, is why I ask you to do this! I’m sure a great many of your other viewers would like this too! Peace and love!